Stirring Motors from CAT ü High power output up to 600 Ncm. Ingenieurbüro M. Zipperer GmbH. Our development makes your success. ü Fuzzylogic control - PDF

Description
M. Zipperer GmbH Our development makes your success Stirring Motors from CAT ü High power output up to 600 Ncm ü Fuzzylogic control ü Soft motor start/stop ü Adjustable safety cut-off function and overtemperature

Please download to get full document.

View again

of 8
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information
Category:

Automobiles

Publish on:

Views: 17 | Pages: 8

Extension: PDF | Download: 0

Share
Transcript
M. Zipperer GmbH Our development makes your success Stirring Motors from CAT ü High power output up to 600 Ncm ü Fuzzylogic control ü Soft motor start/stop ü Adjustable safety cut-off function and overtemperature protection ü Programmable maximal motor speed and torque limitation ü Switch off timer (1min - 99 days) ü Simultaneous display of speed and torque Ingenieurbüro M. Zipperer GmbH D Staufen Telefon / Telefax / R100CT ( pure power up to 600 Ncm) Dear Madam, dear Sir, Why laboratory overhead stirrers? The application of an overhead stirrer in the laboratory environment asks for a number of additional requirements, which only can be met by special developments: An overhead stirrer must allow to be flexibly and safely fixed to a stand Chuck and drive shaft must have an open bore of 10.5 mm minimum to flexibly clamp and adjust the corresponding stirring elements The noise development of an overhead stirrer must be much less than that of ordinary brush motors since the units are used for many hours in labs or pilot plant stations. Overhead stirrers have to be driven at high torque and extreme low speeds on the one hand but also fast on the other hand. Speed control and feed-back speed have to follow very narrow tolerances An overhead stirrer should be easy to operate All operating elements should be easily accessible It is often required to read the set speed from a display Laboratory equipment has to be robust and acid resistant The most important however is: Overhead stirrers have to be safe - this means they should be able to switch off at designated speeds and a set torque. Also lab routine nowadays requires that some overhead stirrers may be connected to a PC via an interface to be driven, controlled and monitored from there. The application in extensive lab superstructures often requires that the overhead stirrer is narrow built and will fit in-between various glass apparatus. All these requirements have been included in the development of our high-efficiency overhead stirrers R100, R80 und R50. Beside these units there are of course some more simple overhead stirrers which are used in schools and for training. Should you require an overhead stirrer with additional features to the ones shown in this brochure please do not hesitate to contact us. We are well prepared to assist you and find a solution for your application. CAT stands for Consultants for Appropriat Technologies. Yours, Manfred Zipperer Overhead stirrer R100CT The powerful pilot plant stirrer for heavy duty jobs. Powerful microprocessor controlled (fuzzy logic) stirrer for optimum performance and accuracy with a maximum torque of 600 Ncm, 240 Watt, hollow shaft and precision chuck of 10.5 mm. The bright back-lit digital display shows all relevant system data (power input, power output and torque) plus simul- R100C R100SD R100C taneous display of set and actual motor speed or time. The display also allows for readout of the absolute or relative torque measurements as well as the power output in watts at the shaft. Speed range rpm with soft start and soft stop logic. Ideal for medium and high viscous media ( mpa s). Other speed ranges (up to 6000 rpm) on request. Torque limits, maximum and minimum motor speeds are programmable. The unit is supplied with an RS232-interface for com puter control. There is also an analogue input for easy remote speed control and analogue output for recorder as well as a programmable switchoff timer. The R100-series is designed for stirring jobs up to 200 litres (related to water); ideal for medium and high viscous media mpa s. Overhead Stirrer R100C The universal laboratory stirring motor for rheometric tests. Same unit as R100CT but with a low speed range rpm and high torque 150 Ncm. A multi-step safety system carries out a self test of all safety functions and detects and protects against overload as well as overtemperature. We also offer units with other speed ranges. For further information please contact us directly. Overhead stirrer R100SD Powerful (low budget) overhead stirrer with 4-digit speed display. The microprocessor controlled speed is steplessly adjustable from rpm. The softstart and soft-stop logic prevents from splashing of liquid. The unit is equipped with an extra long life high performance brush motor. Max. torque 100 Ncm. Hollow shaft and precision chuck at 10.5 mm. The electronic overload and overheat protection shuts off the unit automatically. Thus no damage to the stirrer occurs. This electronic protection applies for all R100 s. Overhead stirrer R100CL Same unit as R100CT but with a speed range from rpm and a higher torque of 250 Ncm; ideal for medium to high viscous media ( mpa s). R80D-PC Overhead stirrer R80-PC Long lasting stirrer with electronic feed-back speed control and digital speed display. This overhead stirrer is especially useful for applications where for a short time dynamic viscosity occurs but a still handy tool is requested. The stirrer comes with RS232 interface for control via a PC. The speed is steplessly adjustable from 20 to 700 rpm. The maximum torque is 80 Ncm. Speed as well as torque are shown on the digital display. Overhead stirrer R80D Same unit as above but without RS232 interface. Both stirrers are equipped with two independent safeguards against overload. They are self-protected through automatic reduction of power intake. CAT LabControl for Windows CAT LabControl for Windows offers full control and documentation of parameters such as speed, torque, switch-off time. This package can be used with CAT overhead stirrers providing an RS232 interface. The control via PC can be put into practice by two means: Sending single commands directly to the unit or controlling the unit with a program which had been written especially for this application. The acquisition of the necessary programming abilities is easy and worthwhile since this will enable you to automate a lot of methods yourself. Performance data may be collected and be shown clearly arranged in diagrams. The performance data can be stored externally and be called up later on again. The data can also be directly printed. The self written programs are lodged in a file and therefore the application may be reproduced at any time. With this powerful software up to 254 units may be operated via an RS232 interface. By assigning different slave addresses to each unit the computer has individual access to each unit Furthermore this program will run at almost any computer, since it only needs a minimum of hard and software. (Pentium1, min 4MB RAM, from Win95) Labcontrol for Windows may be downloaded from our website free of charge. This will provide you with a tool to either writing your own programs for your specific applications or optional one of our software engineers does the job for you at extra cost. R50D R18 Overhead stirrer R50 D Long lasting stirrer with electronic feed-back speed control and digital speed display. This stirrer is well suited for all stirring needs of moderate viscosity in any laboratory, either professional or classroom. The use of the instrument is advantageous where the speed adjustment of stirring processes has to be reproducible -such as when test series have to be carried out one after the other under comparable conditions, and when parallel experiments with several stirrers must be made simultaneously. The speed is steplessly adjustable from 50 to 1600 rpm. The electronic feed-back type of control guarantees exact control and high precision so fluctuations in the viscosity of the media being stirred will not occur. The stirrer has a hollow shaft with a 10.5 mm bore and a heavy chrome plated chuck to avoid corrosion. two independent safeguards against overload. They are self-protected through automatic reduction of power intake. A clamping rod is located at the back of the stirrer for attaching the motor to a stand. Overhead stirrer R18 Convenient and long lasting stirrer with electronic feed-back speed control. Laboratory stirrer for stirring tasks up to 50 litres related to water. Infinitely variable speed from rpm without gear shift. Built-in safety circuit. No blocking; gives indication and protection when overloaded. Ideal unit for the use either in small laboratories or classroom. Ideal for low viscosities ( mpa s). Overhead stirrer R50 The economic and powerful stirring motor for every days lab work. Same unit as above but without digital speed display. The R50 stirrers are equipped with Suitable accessories: All stirrers are suitable for stirring rods and stirring elements with 6, 8 and shaft diameter. Please order from our price list. Stirring Volume (L H2O) Torque Ncm Speed Average Power Intake Chuck mm Dimensions W x H x D mm Weight kg Remarks Modell Powerful Stirring Motors R100CT R100CL R100C R100SD R80D R80D-PC W 220 W 220 W 180 W 100 W 100 W 78x215x170 78x190x170 78x190x170 78x190x170 5, ,3 2,7 Modell R50D R50 R18 Standard Stirring Motors W 85 W 85 W 2,1 2,1 2,1 R2 R1 R17 Handstirrer R1 Handy, battery powered mini-stirrer for mixing liquids of low viscosity in test tubes and other small vessels of up to 500 ml. The stirrer operates on only one AA battery which provides for amazing long lasting use. Easy to use. No cables - no plugs! One of three different stirring rods are available. Plastic (3 mm diameter) All stainless steel for small vessels All stainless steel with large steel blade for max. stirring performance Mini-stirrer R2 Convenient multi-purpose stirrer for small mixing needs in any laboratory, either professional or classroom. A small, quiet and problem-free stirrer designed for long lasting use, comes with clamping bar to be attached to any laboratory stand. The motor is designed for long lasting use and operates at 750 rpm. The unit is fully enclosed and covered by polypropylene to provide protection from chemical spills. Clamping tube and stirring rod are made of stainless steel. Overhead stirrer R17 Convenient and long lasting small laboratory stirrer with electronic feed-back speed control steplessly adjustable from rpm. Comes with a clamp which can be attached to any laboratory stand. Chuck for stirring elements of 4 mm diameter. We offer a special designed stirring paddle in stainless steel which can be ordered together with the stirrer. Stirring Volume (L H2O) Torque Ncm Speed Power Intake Watt Chuck mm Dimensions W x H x D mm Weight kg Remarks Modell Overhead Stirrers R17 R2 R , fix 4 3 ca x64x120 85x60 28x140 1,2 0,26 0,18 Support rod: 180x Support rod: 135x 1,5V Batteries AA Manifold blades for stirring and dissolving Dissolver Blade Stirrer Length including blade Diameter of rod Diameter of blade Propeller Stirrer Length including blade Diameter of rod Diameter of blade 8B B B B B B B B B B B B Centrifugal Stirrer 8B B B B B B B B B B B B B B mm 100 mm 100 mm 8B B B B B B B B B B B B Propeller Stirrer Stirring blade Stirring shaft ø 8x350 Dissolver ø 100 8B B B B B B B U-Stand Special clamp for R100 Software LabControl for Windows PC-connecting cable Pedestal Stand Product Overview Find out more about us, our business fields and products under Technical details are subject to change without prior notice.
Related Search
Similar documents
View more...
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks